PiPo M9Pro 7Gb data partition build #407 KitKat 4_May-14 pre-rooted


This is the latest updated ROM dated 4-May-14 build #407 (most of us are still on #270 or #279)
Remember this update method isthe standard RK update method no additional process or files are needed just use the Rockchip Batch Tool v1.7 (not version 1.5 or 1.6)
Updated to SuperSU 1.74 (no PiPo stock launchers and Slides,Explorer,Logbook etc) with 7Gb data space. This is KASTY's ROM with the beautiful stock PiPo bootanimation.(LATEST release with KitKat version -stable)

THE LINKS HAVE BEEN REMOVED DUE TO AUTHORS REQUESTD:
The links are here (PLEASE VIST THE ARCH TABLET FORUM for support or downloads of the latest firmware updates. : http://www.arctablet.com/blog/forum/

LINKS REMOVED IN PROTEST TO SITES POLICY OF ALLOWING A MINISCULE SIZED "ZIP" FILE. (LESS THAN 100Kb)

NOTE :
I am assuming that you have got all the drivers installed on your Win 7 PC (coz I am on Win7) and cant vouch for the others Win version but the fact remains that you must install the drivers upto the point where whenever you hook up a USB link to your PC from the M9Pro, on your M9pro will show that usb debugging is attached and then the enable usb storage screen will come-up.
Then when you enable the usb storage on your PC will come up with a new usb drive lets say D:/ and E:/. Only when you come up tothis point can you successfully flash your ROM.

Next stage is to run the RK Batch tool and THEN attached it to the M9Pro from the PC.Point it to the Firmware file that you are going to flash. It should show a pink square in the the #1 square. Then the PC and the M9Pro have succeeded in communicating with each other.(HOLD your horses!)

Then, Detached the USB cable from the PC side after the pink square was shown, Then it should go back to all grey when when detached. The M9pro shold be ON and plug-in or at least fully charge.
Press the ESC key on your M9pro and attached it to the PC ( the ESC key will put the M9Pro in an "update mode" if not you will go bald scratching your head to get it going to green) . If you succeeded it will show a green square in the 31 square and then you must press the "RESTORE" button NOT "UPGRADE" button. And then let it run its course it will switch off the screen and then it will come to flashing screen where it hsows the green android then after it finishes it will reboot itself.. the whole process will not take more than 15minutes till to get to your android set-up screen / where you are shown the introductions and setup options.
YOU GOOD TO GO!

The latest KASTY ROM from the Forum ARCHTABLET NEWS : build # 407 with OTA released on 4 May 14 Stable KiTkat version with 7 Gb data partition


Last edited by cracktech on Tue Jun 03, 2014 10:03 pm, edited 1 time in total.
ONDA V975m KitKat beta 3, LENOVO A880 JB S020,
VOYO A18 Exynos 5410 OCTA Core - (25_Dec_13)rooted

PiPo M9Pro (Kasty ROM)ver2.0.13 KitKat 4.4.2, ZTPAD
C93 1f 2Gb data CM10.2 Android 4.3rc3
ZENITHINK : Z102 1G data And 4.04 build 313 , C91 1Gb data And 4.0.4,
SAMSUNG S4 Clone And 4.2.2 MT6589 build I9500ZSUAMDF And 4.2.9(4.2.2)
BHL GALAXY GT-I9300 4.03 Mocordroid 2.2

PiPo M9Pro 7Gb data partition build #407 KitKat 4_May-14 pre-rooted


This is the latest PiPo M9Pro (semi-stock) rooted with 4GB data partition minus all the chinese and Stock PiPo launchers (SuperSu1.6)) busybox added no problems about hangs, bootanimations, it is close to stock firmware as possible except that no TWRP/CWM recoveries (what the hell for?). It is for M9Pro with OTA facilities workking but on the present version PiPo didnt implement their update service well so it it will fail to do an OTA successfully. If ever the screen ask you for permission to upgrade from v1.00 to version 1.01 just click "NO" if you click YES your power up will show an Android bot with its belly up a.All you have to do then is to reset via pin hole at the back but beeter NOT to upgrade and to stp the nagging go into the build.prop the 2nd last line there is a statement for OTA server upgrade just put in "## at the beginning of the line. to make that line redundant

The download links(RETRACTED): PLEASE SEE THE ABOVE MESSAGE FOR LINKS
Last edited by cracktech on Mon Nov 18, 2013 10:17 pm, edited 1 time in total.
ONDA V975m KitKat beta 3, LENOVO A880 JB S020,
VOYO A18 Exynos 5410 OCTA Core - (25_Dec_13)rooted

PiPo M9Pro (Kasty ROM)ver2.0.13 KitKat 4.4.2, ZTPAD
C93 1f 2Gb data CM10.2 Android 4.3rc3
ZENITHINK : Z102 1G data And 4.04 build 313 , C91 1Gb data And 4.0.4,
SAMSUNG S4 Clone And 4.2.2 MT6589 build I9500ZSUAMDF And 4.2.9(4.2.2)
BHL GALAXY GT-I9300 4.03 Mocordroid 2.2

You need to be logged in to the site to leave comments.

Login  •  Register



Return to “Pipo Tablets”



Who is online

Users browsing this forum: No registered users and 3 guests